Recent content by Tony54

  1. T

    New Moscow plus 48v, 16a battery only showing 53.4v.

    Hi all responders, Thanks for all your inputs, I put the battery on charge again and the charger shut off at 53.9 no load measured with a voltmeter. I'm going to accept the battery because I know the battery is giving a good distance without problems. Incidentally, I was going to buy a 3000 to...
  2. T

    New Moscow plus 48v, 16a battery only showing 53.4v.

    Hi Timpo, I have sold the Venice, I enjoyed using it but it was slightly too big a frame. I then put a bafang BBS mid drive motor into my decathlon triban hybrid bike which is great on roads and smoother canal paths but not for rougher tracks. So bought the ncm for the rougher tracks. I've put...
  3. T

    Bafang motor and spares in Spain.

    Thanks surly, That shop is just perfect. Tony
  4. T

    Bafang motor and spares in Spain.

    Hi, I've just moved to Spain and am trying to find a Spanish supplier of bafang motors and parts. I'm looking to buy a mid drive motor because my trusted seller in uk doesn't post to Spain. And now that UK is not in the EU anymore I would have to pay import tax. I could buy from any EU...
  5. T

    New Moscow plus 48v, 16a battery only showing 53.4v.

    Hi Timpo, Yes, I'm trusting the display read out. Is their a recommended point to test the voltage? I suppose I could voltmeter across the battery terminals with the battery disconnected but this would be an unloaded voltage is apposed to when the display is turned on, but don't suppose there...
  6. T

    New Moscow plus 48v, 16a battery only showing 53.4v.

    Hi all, This is my second ncm new bike. I did my Venice after two years of good use. But I noticed that it only charges to 53.4 volts when the charger cuts off. I tried another 2 amp charger and the same result. I rang the ncm rep and he said it is normally this low, but on my past Venice and...
  7. T

    Bacang bbs02 pas spare parts uk or anywhere

    Gionni, Right on cue, thanks.
  8. T

    Bacang bbs02 pas spare parts uk or anywhere

    Hi Gionni, Thanks for the heads up re green bike kit, I had a look at their website and it seems a well stocked site. Yes, I can't see the magnetic wheel being broken, but you never know. I've never opened the bafang more than replacing a controller and checking the connections so that's my...
  9. T

    Bacang bbs02 pas spare parts uk or anywhere

    Hi, As mentioned elsewhere I have a non working pas on my bbs02 . and I've narrowed it down to a faulty pas pcb or the magnet assembly. Because I bought a second motor, I've been able to swap components around including displays units, so know its not a programming fault. Everything works except...
  10. T

    Bafang 500W Mid Drive Kit Availability

    Hi, I bought a bafang from china using amazon.co.uk, it took several months and made the mistake of fitting it to the bike before testing. It had 3 faults, a faulty controller, a faulty speed sensor and the pedal assist wouldn't work. After a month of not being able to ride my bike, I had a new...
  11. T

    New controller for bafang bbs02 500w

    Thanks Hi Harry, I'm asking myself the same question. Some of the smaller connectors aren't the best quality. Just not enjoying the thought of undoing the controller again. The upshot is that I won't buy anything expensive from China again.
  12. T

    New controller for bafang bbs02 500w

    Thanks A Hicks, I think the speed sensers cable comes straight from the controller. It's a new controller so doubt it could be wrong but the original controller was unserviceable so don't know. I hope it's not a bad connector in the controller, it's a pain taking the controller off. Could it...
  13. T

    New controller for bafang bbs02 500w

    Gionni, Thanks for your help, I've checked the cable connections and settings on my p850c controller to no avail. What I've noticed is that there is a red led on the speed sensor which doesn't light up. I'm not sure if it is supposed to light when the magnet passes the sensor or all the time...
  14. T

    New controller for bafang bbs02 500w

    Hi guys, After a long break, I've just fitted the new 500 watt controller to my 500w bafang motor and it's half working., It works on throttle and the display is working and the previous error 30 has gone. The problem now is that the pedal assist isn't working. Could there be something 'silly'...